23
February

Bộ chia tín hiệu 3109 PR Elelctronics

CTY ÂU MỸ LÀ ĐẠI LÝ HÃNG PR ELECTRONICS TẠI VIỆT NAM

CHUYÊN CUNG CẤP BỘ CHIA TÍN HIỆU 3109, BỘ CHUYỂN ĐỔI TÍN HIỆU 4114, BỘ CÁCH LY TÍN HIỆU 5104

THÔNG SỐ KỸ THUẬT BỘ CHIA TÍN HIỆU 3109:

Technical Data

Input

Input signal
(calibrated switchable)
0 to 20 mA, 4 to 20 mA, 0 to 5 V, 0 to 10 V, 1 to 5 V, 2 to 10 V
Input resistance Current input
Voltage input
≤ 35 Ohm
≥ 100 kOhm
Overload Current input
Voltage input
< 50 mA
< 30 V
Transmitter supply Tx
(switchable)
16 V (open circuit voltage/short circuit current ≤ 22 V/35 mA)

Output I + II

Output signal
(calibrated switchable)
0 to 20 mA, 4 to 20 mA, 0 to 5 V, 0 to 10 V, 1 to 5 V, 2 to 10 V
Load Current output: ≤ 6 V (300 Ohm at 20 mA) Voltage output: ≤ 5 mA (2 kOhm at 10 V)
Linear transmission range -1 to +110 %
Ripple < 10 mVrms

General Data

Transmission error < 0.1 % full scale
Temperature coefficient 1) < 100 ppm/K
Cut-off frequency -3 dB 5 kHz
Response time T99 150 µs
Test voltage 3 kV AC, 50 Hz, 1 min, Input against Output I against Output II against power supply
Working voltage 2)
(Basic Insulation)
Up to 600 V AC/DC for overvoltage category II and pollution degree 2 acc. to EN 61010-1 between all circuits.
Protection against electrical shock Protective separation according to EN 61140 by reinforced insulation in accordance with EN 61010-1 up to 300 V AC/DC for overvoltage category II and pollution degree 2 between all circuits.
Ambient temperature Operation
Transport and storage
–25 °C to +70 °C   (-13 to +158 °F)
–40 °C to +85 °C   (-40 to +185 °F)
Power supply 24 V DC       16.8 V to 31.2 V DC, approx. 1.4 W
EMC 3) EN 61326-1
Construction 6.2 mm housing, protection class: IP 20, mounting on 35 mm DIN rail acc. to EN 60715
Weight Approx. 70 g
  1. Average TC based on the final value in specified operating temperature range
  2. As far as relevant the standards and rules mentioned above are considered by development and production of our devices. In addition relevant assembly rules are to be considered by installation of our devices in other equipments. For applications with high working voltages, take measures to prevent accidental contact and make sure that there is sufficient distance or insulation between adjacent situated devices.
  3. Minor deviations possible during interference

Block diagram

dn21000

Dimensions

masszeichnung-mitBus

Connection
Captive plus-minus clamp screws
Wire cross-section max. 2.5 mm² / AWG 14
Stripped length 6 to 8 mm / 0.28 in
Screw terminal torque 0.8 Nm / 7 lbf in
Optional power connection via In-Rail-Bus (see accessories)

Terminal assignments

1 Input    -I   +U   +Loop
2 Input    +I   -U   -Loop
3 + Output II
4 Output II
5 + Output I
6 Output I
7 + Power supply (connected to In-Rail-Bus)
8 Power supply (connected to In-Rail-Bus)

 

Liên hệ để được tư vấn:

Thanks and best regards

Long Tran

Mob.: +84 909 006 435

Email.: long.tran@aumyco.com

AU MY technology Service Trading Company limited

Add.: 93/36 Street 02, Tam Binh Ward, Thu Duc District, Ho Chi Minh city, Vietnam

Tel.: +84 3 816 2902      Fax: +84 3 816 2902

Web.:    www.aumyco.com          Email.: info@aumyco.com

www.tbcongnghiep.com

www.chuyendoitinhieu.com

www.doluongcongnghiep.com

Leave a Reply